Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
We've uncovered this great article about A Step-by-Step Guide to Installing a Bathtub below on the web and concluded it made perfect sense to relate it with you here.
Setting up a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard task. If the old tub is readily accessible, the task can move rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new bath tub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the new one. Ensure you have qualified on your own for the work and also fit trying it. As opposed to working with a professional to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This short article will aid you mount a brand-new tub in your bathroom if you have actually currently purchased a brand-new bathtub and do not need to alter the plan of your previous water supply pipelines.
Your tools and product checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome because of the limited accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipes. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washers remain in place in between the faucet and also the sink. Secure the tap in position with the producer supplied backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former kind ought to be connected to the tap ends first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the bathtub in the called for placement. The wood boards are helpful in equally spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the level reviews degree.
To set up taps, fit the bottom of the outermost versatile faucet port to the proper supply pipeline by making a compression join; then do the same for the other faucet.
Turn on the supply of water and also inspect all joints and new pipework for leakages and tighten them if needed. Load the bath tub as well as additionally inspect the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait till the tub has actually been utilized at the very least once as this will settle it into its final position.
Planning for the Installation
First of all, the supporting frame provided with the bath must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its final placement.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, leading to issues with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to permit the movement experienced when the tub is in use. The sealant can split relatively early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up about Installing A Bathtub from a friend on a different website. Are you aware of somebody who is looking into the topic? Take a moment to share it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Start Now Report this page